Thermocouple Probes

Type K High Temperature Probes

connectorPlastic handles and thermocouple plugs are rated for short term exposure of 250°F (121°C) and extended exposure of 212°F (100°C). Sensor and cable ranges are listed for each probe.
Thermocouple Probe Quick Selection
Immersion/General Purpose

Smoke House Penetration Probe - Stainless Armor

Model: 113-178

ThermoWorks Image
Penetration probe used by commercial smokehouses. The 78" cable is covered by a flexible stainless steel armor and has a wider temperature range. It will survive longer than other probes when stepped on, manhandled, kinked, slammed in doors or exposed to the higher temperatures of outdoor grills. It should be protected from direct exposure to flames and should not be immersed past the stainless probe section. The armor is not easily closed in a regular home oven door, so choose a different probe for standard kitchen use. You can still break this probe if you try, but it is the toughest probe available to backyard grillers.
Sensor Range: -77 to 662°F (-75 to 350°C)
Transition (SST): Max temp 662°F (350°C)
Cable: -77 to 662°F (-75 to 350°C)
Cable Diameter: 0.2 inch (5mm) dia.
Time Constant: Less than 2 seconds typical in liquid. Less than 10 seconds full reading.
Accuracy: ±0.9°F (±0.5°C) from 32 to 212°F (0 to 100°C)



Crocodile Clip Oven Probe

Model: 113-041

ThermoWorks Image
The Crocodile Clip Oven Probe is used by commercial kitchens to calibrate and profile ovens and grills. A stainless steel overbraid protects the probe and a fiberglass inner sheath protects the 78" lead. The clip can be easily attached to an oven rack and allows you to place it right where you need it. Great for monitoring grill temps during roasting, searing or smoking.
Sensor Range: -58 to 660°F (-50 to 350°C)
Cable: -77 to 660°F (-75 to 350°C)
Time Constant: Less than 2 seconds typical in liquid. Less than 10 seconds full reading.
Accuracy: ±0.9°F (±0.5°C) from 32 to 212°F (0 to 100°C)


High Temp Flexible Ceramic Fiber-Insulated Probe

Model: WD-08467-64/WD-08467-64-10

ThermoWorks Image
The High Temp Flexible Ceramic Fiber Insulated Probe is used in commercial ovens and furnaces. Good choice to monitor fireboxes, kilns, grills, etc. However, it's not designed for direct food measurements.
Sensor Range: -58 to 2200°F (-50 to 1204°C)
Cable: -58 to 2200°F (-50 to 1204°C)
Time Constant: Less than 1 seconds typical in liquid. Less than 5 seconds full reading.
Accuracy: ±0.9°F (±0.5°C) from 32 to 212°F (0 to 100°C)
Select probe and add to cart


High Temp Wire Probe

Model: 113-382/383/385

ThermoWorks Image
The High Temp Wire Probe is a good low-cost high temp probe for ovens and backyard grills. It's protected with a fiberglass insulation, however, you should avoid using it over 660°F. Avoid direct immersion in liquids or direct contact with food. Available in multiple lengths.
Sensor Range: -77 to 660°F (-75 to 350°C)
Cable: -77 to 660°F (-75 to 350°C)
Time Constant: Less than 0.5 seconds typical in liquid. Less than 2.5 seconds full reading.
Accuracy: ±0.9°F (±0.5°C) from 32 to 212°F (0 to 100°C)
Select probe and add to cart

From:


High Temp Alligator Clip Oven Probe

Model: 8468-22

ThermoWorks Image
The High Temp Alligator Clip Oven Probe is used by commercial kitchens to calibrate and profile ovens. A stainless steel overbraid protects the probe and a fiberglass inner sheath protects the 120" lead. The clip can be easily attached to an oven rack and allows you to place it right where you need it. Great for temporary monitoring of oven temps during roasting or baking.
Sensor Range: -58 to 900°F (-50 to 482°C)
Cable: -103 to 900°F (-75 to 482°C)
Time Constant: Less than 1 seconds typical in liquid. Less than 5 seconds full reading.
Accuracy: ±0.9°F (±0.5°C) from 32 to 212°F (0 to 100°C)


Precision Surface Probe

Model: 103-030/303-030

ThermoWorks Image
This is the fastest and most accurate handheld surface probe we've seen. Readings generally take less than 5 seconds! The sensor is made from flat-spring ribbons of thermocouple material. Very popular in equipment servicing applications and in the plastics and packaging industries.
Sensor Range: -58 to 482°F (-50 to 250°C)
Handle (ABS blend): Max temp 221°F (105°C)
Cable: 14 to 221°F (-10 to 105°C)
Time Constant: Less than 0.5 seconds typical in liquid. Less than 2.5 seconds full reading.
Accuracy: ±0.9°F (±0.5°C) from 32 to 212°F (0 to 100°C)
Select probe and add to cart

From


Right Angled Precision Surface Probe

Model: 103-032/303-032

ThermoWorks Image
Same sensor design as above but with a right angle bend in the shaft to improve access where the surface is hard to reach.
Sensor Range: -58 to 482°F (-50 to 250°C)
Handle (ABS blend): Max temp 221°F (105°C)
Cable: 14 to 221°F (-10 to 105°C)
Time Constant: Less than 0.5 seconds typical in liquid. Less than 2.5 seconds full reading.
Accuracy: ±0.9°F (±0.5°C) from 32 to 212°F (0 to 100°C)
Select probe and add to cart


Heavy Duty Surface Probe

Model: 103-020/303-020

ThermoWorks Image
Rugged and durable design covers a very wide range. Used in many industries for high temperature metal surfaces.
Sensor Range: -58 to 1832°F (-50 to 1000°C)
Handle (ABS blend): Max temp 221°F (105°C)
Cable: 14 to 221°F (-10 to 105°C)
Time Constant: Less than 1 second typical in liquid. Less than 4 seconds full reading.
Accuracy: ±0.9°F (±0.5°C) from 32 to 212°F (0 to 100°C)
Select probe and add to cart


Right Angled Heavy Duty Surface Probe

Model: 103-028/303-028

ThermoWorks Image
Same as above but with a bend in the shaft for hard to reach surfaces.
Sensor Range: -58 to 1832°F (-50 to 1000°C)
Handle (ABS blend): Max temp 221°F (105°C)
Cable: 14 to 221°F (-10 to 105°C)
Time Constant: Less than 1 second typical in liquid. Less than 4 seconds full reading.
Accuracy: ±0.9°F (±0.5°C) from 32 to 212°F (0 to 100°C)
Select probe and add to cart


Surface Probe

Model: 103-000/303-000

ThermoWorks Image
This easy to use surface probe features a 1/4" copper disc that is spring loaded and fit inside a stainless steel shaft. The shaft end is cut and bent into a tripod to aid in positioning the sensor flat against a surface. The wide range makes this probe useful in a wide variety of industrial uses.
Sensor Range: -58 to 1112°F (-50 to 600°C)
Handle (ABS blend): Max temp 221°F (105°C)
Cable: 14 to 221°F (-10 to 105°C)
Time Constant: Less than 2 seconds typical in liquid. Less than 10 seconds full reading.
Accuracy: ±0.9°F (±0.5°C) from 32 to 212°F (0 to 100°C)
Select probe and add to cart


Washer Thermocouple

Model: 113-440/MC

ThermoWorks Image
Easy method to measure surface temperature permanently. The thermocouple sensing junction is located on a washer with a 1/4" diameter hole for bolting to the surface to be measured. Each probe is supplied with a 78" braided stainless steel cable for durability. Order with bare lead termination for panel meters or controllers or a mini-connector for plugging in to a handheld meter.
Sensor Range: -77 to 660°F (-75 to 350°C)
Transition (SST): Max temp 660°F (350°C)
Cable: -77 to 660°F (-75 to 350°C)
Time Constant: Less than 2 seconds typical in liquid. Less than 10 seconds full reading.
Accuracy: ±0.9°F (±0.5°C) from 32 to 212°F (0 to 100°C)
Select probe and add to cart

From:


5" High Temp Handheld Probe

Model: 103-212/303-212

ThermoWorks Image
A popular general purpose probe that will withstand a very wide temperature range. The shaft is mineral-insulated stainless steel that can be bent without adversely affecting performance. Use this probe for liquids and hot air or gases.
Sensor Range: -58 to 2012°F (-50 to 1100°C)
Handle (ABS blend): Max temp 221°F (105°C)
Cable: 14 to 221°F (-10 to 105°C)
Time Constant: Less than 2 seconds typical in liquid. Less than 10 seconds full reading.
Accuracy: ±0.9°F (±0.5°C) from 32 to 212°F (0 to 100°C)
Select probe and add to cart


1/16" Dia. High Temp Probe

Model: 103-204/303-204

ThermoWorks Image
Same as 5" version above but with a 1/16" diameter sheath. This version provides faster response times and the probe is a bit easier to bend for fitting into holes or between objects.
Sensor Range: -58 to 2012°F (-50 to 1100°C)
Handle (ABS blend): Max temp 221°F (105°C)
Cable: 14 to 221°F (-10 to 105°C)
Time Constant: Less than 2 seconds typical in liquid. Less than 10 seconds full reading.
Accuracy: ±0.9°F (±0.5°C) from 32 to 212°F (0 to 100°C)
Select probe and add to cart


High Temp Industrial Probes

Model: 113-420/425

ThermoWorks Image
The High Temp Industrial Probes go to very high temperatures and the stems are completely sealed against moisture. The mineral insulated sheath can be easily bent to any shape and is perfect for high temp ovens and furnaces, and are often used as long-term solutions to monitoring fireboxes and grill hoods. They can also be semi-permanently installed and will resist the weather and steam, The 78" cable is PTFE so it should be kept below 500°F, but the metal sheath section can go to 2,012°F! Available in two diameters, 1/16" or 1/8". The smaller diameter is faster and somewhat easier to bend. The larger diameter normally survives longer however, both should last for many years with modest care. Longer cables available upon request.
Sensor Range: -58 to 2012°F (-50 to 1100°C)
Transition (SST): Max temp 221°F (105°C)
Cable: 14 to 221°F (-10 to 105°C)
Time Constant: Less than 2 seconds typical in liquid. Less than 10 seconds full reading.
Accuracy: ±0.9°F (±0.5°C) from 32 to 212°F (0 to 100°C)
Select probe and add to cart

From:


Plug-Mounted Mineral Insulated Probe

Model: 113-213

ThermoWorks Image
Flexible, high temperature, stainless steel, rounded tip mineral insulated probe. Ideal for measuring high temperature liquids.
Sensor Range: -58 to 2012°F (-50 to 1100°C)
Transition (Plug): Short term exposure of 250°F (121°C) and extended exposure of 212°F (100°C)
Time Constant: Less than 2 seconds typical in liquid. Less than 10 seconds full reading.
Accuracy: ±0.9°F (±0.5°C) from 32 to 212°F (0 to 100°C)


Coiled Type K Extension Lead

Model: XCK-2M-MF

ThermoWorks Image
Extend the reach of your probe with this probe extension lead. Cable is coiled and works with type K probes and meters. Features a plug on one end and socket on the other. Length is 79" (2 meters) from plug to socket.
Cable: 14 to 221°F (-10 to 105°C)


Straight Type K Extension Lead

Model: XSK-3M-MF

ThermoWorks Image
Extend the reach of your probe with this probe extension lead. Cable is straight and works with type K probes and meters. Features a plug on one end and socket on the other. Length is 118" (3 meters) from plug to socket.
Cable: 14 to 221°F (-10 to 105°C)

Icon Legend
Icon Category Icon 1
Icon Category Icon 2
Icon Category Icon 3
Icon Category Icon 4
Icon Category Icon 5
Icon Category Icon 6

Our Company


 

Gift Wrap

Gift Wrapping

We'll wrap your gift in our custom gift paper, trimmed with a bow and gift tag. The rich, graphite and silver combination is suitable for any occasion or anybody.

Enter a custom message for the handwritten tag (Up to 50 characters). Cost for wrapping is $4.99 per item. Each item wrapped separately. Selectable in the order info where available. Some items can not be wrapped.

Ordering more than one of the same item but don't want them all wrapped? Just add each item you want wrapped to your shopping cart individually and select the wrapping option. Add your custom greeting for each wrapped item separately as you add the item to your cart.